Triple play fiber optic network box, triple play fiber splicing box, fuse box straight triple play fiber, triple play fiber optic distribution boxes, triple play fiber optic splitter boxes, triple play fiber optic corridor Box, tri -play fiber optic wiring boxes, triple play fiber optic sub-fiber boxes, triple play optical fiber distribution boxes, Model: 24 cores, 32 cores, 48 ??cores, 72 cores, 96 core, 144 core specifications: 750 * 600 * 180,700 * 140,700 * 600 * 600 * 120, 600 * 500 * 120 Material: cold-rolled plate, stainless steel Installation: wall-mounted, hold pole, wall-mounted, embedded, mosaic, outdoor and indoor etc. Waterproof function uses district: Telecom Mobile Unicom Railcom FTTH FTTB FTTX FTTP Cixi City for Wyatt Communication Equipment Co., Ltd. specializes in telecommunications, mobile, China Unicom, China Railcom, radio and television supply ancillary products, triple play fiber optic network box Overview: triple-play A fiber-optic network box namely China Mobile, China Unicom, China Telecom along with the progress of society, due to the development of business and technology, the case of mutual penetration of new products and the development of mutual integration. Including spectral sub-fiber box, corridor integrated boxes, fiber boxes, etc. corridor. Suitable for cable and wiring pigtail protective connection, or fiber access network fiber termination point. Also applies to the use of FTTH fiber to the home, it can be installed in the corridor, basement, room and building facades. After splitting the cable can also drop cable wiring box and weld leads, achieve cable features to meet the needs of various transport network project. For the cable and optical communications equipment wiring connection through the wiring box adapter, optical fiber jumper leads signal, the optical wiring function. Suitable for FTTH project using cable to the rear floor, installed in the corridor, basement, room and building facades. You can also dial after opening the cable coiled welding leads and drop cable wiring box by splitting achieve straight-through cable capabilities to meet the needs of traditional transmission network project. Triple play fiber optic network box Technical parameters: Working temperature: -40 ℃ ~ + 60 ℃ Humidity: ≦ 95% (+ 40 ℃) Atmospheric pressure: 70kPa ~ 106 kPa door opening angle: 180 ° grounding strip withstand voltage Level: ≥3000V (DC) / 10mA / 1min Insulation resistance: ≥2 × 1020MΩ500V Features: triple play fiber optic network box advantages: 1. Body material quality cold-rolled plate (Q235-A) made box epoxy powder coated, corrosion resistant, anti-aging; 2. Effective achieve Mobile, China Unicom, telecommunications triple-play. Space saving construction and construction strength. 3. Take the left and right and up and down the structure structure composite structure design, both sides have a layer of fiber splicing and the right upper optical splitter wiring layer and the lower layer of fiber splicing. 4. consistent form and thickness of the chassis, the construction process to meet any form of connecting 5. part made from ABS plastic material parts; 6. two-tier structure design, the upper wiring layer optical splitter, the lower layer of the fiber splicing; 7. optical splitter module drawer-type module design, with a strong interchangeability and versatility; 8. Using turn plate structure, can be high-density port configurations and spectroscopic facilities. 9. accord (YD / T988-2007 communication cable transfer box requires triple play fiber optic network box Applications: Suitable for FTTH project using cable to the rear floor, installed in the corridor, basement, room and building facades cable is also available. After splitting wiring box home store fiber coiled fiber optic cable splicing and leads to achieve direct function of the cable to meet the needs of traditional transmission network engineering cable connector box cable connector box cable is two or more connected together and having connecting portion of the protective member is cable line construction must be used, and is one of the very important equipment, quality cable connector box directly affects the quality of life of fiber-optic cables and fiber optic lines. 1 Introduction cable connector box is popular called, school called cable continued boxes, also known as the cable continued pack, cable connector package and barrel. of mechanical pressure seal fitting system is provided adjacent the optical fiber cable, splice protection device seal and mechanical strength continuity. The main is applicable to various structures in straight overhead cable, pipeline, direct burial and branch laying method of connection. box of imported reinforced plastics, high-strength, corrosion resistance, terminal structure suitable for the connection of the cable terminal room, maturity structure, reliable sealing, easy construction widely used in telecommunications, networking systems, CATV cable, fiber optic cable network system, and so the right side is binary two splice case;.. for the protection of the cable between two or more connection, fiber optic distribution, is one of the common user access point device, the main role to complete the connection cable distribution cable and home line outdoors, and can be installed cassette or simple optical splitter according to FTTX access; product characteristics? cassette products of high quality plastic products using secondary pressure cable technology to ensure the box without additional attenuation fiber products with multiple reuse and expansion function Technical Specifications Dimensions:?.?.? height 430mm maximum outside diameter of the inner diameter Φ135mm ? Φ210mm cable into the throat: Φ20mm single disc Core:? 12/24 maximum splice tray:? minimum capacity 4-cell maximum capacity of 144 core maximum number plate Splice:? 6 stretch tightness:? 2000N axial tension , no leakage breakdown voltage:.? 15KV (DC) stretch seal:? After the inflatable product can withstand 2000N axial tension, the impact of seal airtight:? product after inflation, can withstand the impact energy 16N * m (Newton * m) the impact of the three, the product without cracks, no leakage.? Other requirements are in line with the performance of YD / T814.1-2004 standards. connector 1 according to shape classification structure can be divided hat cable connector Both boxes and horizontal cable connector box; The methods are overhead cable laying, pipe (tunnel) and buried and other types; 3. cable connection is divided into two successive straight-through connection and differences; 4. sealed manner There Shrink sealed type and mechanical seal type. [1] cable connector box (5) specifications identified in accordance with YD / T814.1-2004, model code should reflect the professional products, the Lord calls the code, using the occasion Code, cable connectors mode code, the code-tight manner and specifications, product model configuration is shown by the following sections: for example, the three divisions of the mark cable connector box sealed with mechanical seal manner 24 core aerial cables expressed as: GJSxx-JF3K24. 2 General Requirements 1. With the recovery of the cable sheath integrity and continuity of the cable stiffening member of mechanical properties. 2. Provide the cable in electrical communication with the metal member, grounding or disconnect feature. 3. With the fiber connectors from environmental influences performance. 4. Provide placed over fiber optic connectors and optical storage function left. 5. If required, fiber optic splice closure also has anti-termite properties. 3 performance fiber optic connector after the connector box protection against tidal erosion should be, should not increase the attenuation of the optical fiber connector protector before, and meet the following requirements: optical properties remaining cable connector box fiber coiled in the fiber placed within the device In operation cable connector box installation of fiber optic connectors should be no significant additional attenuation. After sealing cable splice closure procedures prescribed complete package, cable connector box filling pressure (100 persons 5) kPa, soaked in room temperature water for 15 minutes to observe vessel stability should be no bubbles escape, or stable 24-hour observation barometer instructions should change. Test resealed performance fiber optic splice closure according to the procedure prescribed packaged repeated three times. Cable connector box filling pressure l00kPat5kPa, soaking in room temperature water for 15 minutes to observe vessel stability should be no bubbles escape, or stabilization was observed 24 hours barometer instructions should change. Mechanical properties after the following test, the parts cable connector box and the cartridge box should not change, do light for inspection or examination necessary to open the cassette. The following tests shall be in charge cable connector box man (60 persons 5) kPa pressure, the pressure should not change after the test; immersion in water at room temperature was observed 15 minutes to stabilize the vessel should be no bubbles escape or observe 24h steady barometer index It should change, housing and the member should be no cracks, damage and significant deformation. 4 to install fiber optic cable preparation 1. Remove the skin, (if there is, remove the shield and armor) each wrapped layer is then removed to expose the loose tube, the specific method, please press the cable manufacturer's recommended standard method steps, preliminary length 3 m. 2, use detergents and strengthen the core loose tube sheath, remove excess filling casing, the cable sheath 150mm long polished with sandpaper to offer. 1 cable installation, cable diameter selected according to the minimum inner diameter of the seal ring, and two sealing ring on the cable. 2, the optical cable into the corresponding hole. 3, connecting the shielding and grounding. 4, between the two sealing rings on the self-adhesive sealing tape wrapped around the sealing tape around the outer diameter of the seal ring flush to form a cable sealing end. 5, the cable seals the cable end into the hole. 6, with hose clamps through the cable holder and the cable core stiffener bracket, the cable connector box secured to the base, tighten the screw hose clamps, hose clamps until tightening up. 7, on the cable tie nylon cable ties, cut excess length. 8, the remaining unused cable holes, please sealing plug. The same block head wound sealing tape, the same requirements and 5.2.4. 9, the reinforcing member wrapped around the splice tray holder countersunk screws, and pressed. The optical fiber connector 1, late on a preliminary 1.5 turns coiled fiber, then the fiber all over the body coiled in the box. 2, please use the disc on a single fiber single buffer tube, the ribbon fiber plate Please ribbon buffering tube. At the entrance of the splice tray fastened with nylon ties. 3. The method according to the provisions of the docking of two (with) fiber splice connector card into the card slot unit, more than long please coiled in the tray. 4, splice tray cover, press on until it clicks into place. 5, according to the capacity needed for different connector box, determines the number plate weld overlay plate, the splice trays superimposed type optical fiber connector must meet snap welding unit and the inspection and maintenance requirements. Every two superposed splice trays can be six holes on the rubber fold, respectively, each of the three projections stuck on the upper and lower plate twist; four rubber folding, symmetrical positions of the two sides of the disc, such as the superposition of five Splice double-layer disc in accordance with the method described above with three buckle, three and four disc tray fastened, four and five disc tray fastened, and so five disk to stably superimposed together . When it is desired to maintain a certain level view or disc fusion cases, as long as one side of the upper plate of the two-piece folding buckle removed, splice tray can be as open as open book page. Cassette seal 1, box package: package first before the cartridge valve tip and the ground screw and tighten. ? The sealing strip embedded in the cartridge seal around the tank;? At both ends of the connector box "U" channel into the trench were also used at the seal. Note: Use the seal, do not artificially stimulate seal, to prevent leakage. 2, the connector box gently close the cover, screw fastening bolts fastening cover the order indicated in numerical order and tightened with a torque wrench ban solid, torque reaches 25N? M. 3. After 5 minutes, then a torque wrench, tighten the torque still reach 25N? M. Removing the cover 1, according to the order of release fastening bolts 10, when the lid and the seat were still together. 2, take four fastening bolts are inserted into the cartridge body corners, symmetrical, evenly screwed into the four corners of the lid, the lid and the seat isolated up 6mm. 3, wait five minutes and then evenly cover the lid and seat separation> 6mm, can be easily separated by hand until the lid and the seat. Note: When you need to gently separate removable cover, so as not to damage the fiber splice. 4. Capacity or inspection, the need to re-close the cover, you must remove the old seal, re-laying seal to seal groove, including sealing "U" channel cable entry end. Optical fiber distribution boxes Product Name: fiber optic distribution boxes Product Description: cable junction box is FTTH system wiring sub-line subscriber terminal equipment, optical fiber fusion can be achieved, allocation and scheduling. Product Overview sub-fiber optical cable box is used for FTTH construction primary or secondary spectroscopic splitting different scenarios and development and design needs, an important branch point wiring devices used as the light. The products are used in home wiring cable through an optical splitter cable connect with the user butterfly, enabling the user to open FTTH business, it is an important light ODN network access point. Technical indicators 1, design and manufacturing in line with BS6497, ANSI / EIA RS-310-C and DIN41491 PART1 international industry certification standards. 2, the surface anti-static coating with high hardness noodles, reached the international standard BS6497. Dimension line with GB / T3047.2-92; 3, in line with international standards nontoxic. 4, protection class design basis GB4208-1993 standard indoor enclosure protective performance reaches IP53 grade, outdoor cabinet reaches IP55 level protection performance. Product Features 1, cabinets reasonable arrangement couplers and splice tray, and a fixed plate and cable management rings for cable management. 2, box made of high strength cold rolled steel, welded frame design, indoor cabinet vertically reservation cable import and export, the lower part of outdoor cabinet set aside the cable import and export, easy cable management. 3, box made of high strength cold rolled steel processing, front single door mechanism, door protection strips set, can effectively play a protective role. 4, sub-fiber optical cable box has a cable entry, fixation and protective devices to protect the core cable and cable from damage, and to achieve fusion and sub-fiber cable. Features: can be flexibly configured 1X32,1X16,1X8 or 1X4 and other optical splitter, easy to install fiber optic cable through the access opening ring into the box, complete disagreement and management without cut off; and pigtails ﹑ fiber tray storage plenty of space; a reasonable go full fiber routing design; fiber bend radius not less than 30mm; differences fiber optic cable ﹑ ﹑ optical splitter pigtails, fiber jump out ﹑ independently without disturbing each other; for FC ST and other ﹑ ﹑ SC adapter, flexible configuration ﹑ fast installation. Environment sub-fiber box Fiber Optical Fiber Distribution Box 1 Working conditions must be specified in the following table work reliably. Type Operating Conditions Temperature Relative humidity Atmospheric pressure indoor -10 ℃ ~ + 40 ℃ ≤85% (+ 30 ℃) 70kPa ~ 106kPa outdoor -40 ℃ ~ + 60 ℃ ≤95% (+ 40 ℃) 2 appearance and the appearance of a structure ) corridor (indoor and outdoor) optical sub-fiber box housing should be complete, all plastic parts no glitches, no bubbles, no cracks, no holes, no warping, no impurities and other defects, heat distortion temperature ≥85 ℃, meet line 15-year service life requirement. b) corridor (indoor and outdoor) optical sub-fiber sheet metal box inside the box using the Q235 cold-rolled sheet, thickness not less than 1.2mm, surface galvanized, housing bottom mounting plate with Q235 cold rolled sheet, thickness not less than 2mm ,, galvanized after spray treatment. Another outdoor pole mounting configuration iron, stainless steel or galvanized iron attachment process. c) spray metal structure, the coating and the substrate should have good adhesion, adhesion should not be less than GB, T 9286-1998 standard Table 1, 2 requirements. Smooth surface, uniform color, there is no peeling, paint, rust and other defects, no sagging, scratches, open at the end, bubbles and white and so on. d) corridor (indoor and outdoor) of non-metallic composite materials (plastic) fiber optic sub-fiber box accessories used, combustion performance should be consistent with GB, the 2408-2008 regulations T, e) corridor (indoor and outdoor) optical sub-fiber box surface coating color chromatically: GSB05-1426-200 in gray (the same color reference Pantone - 445 gray, matte color). f) fiber optic wiring box front left side of the box must have a China Unicom LOGO logo, color is red, according to China Unicom, the same proportion trademark scaling. g) surface color fiber optic wiring boxes should facilitate the identification and labeling of, and in harmony with the environment. h) inside the unit of work surfaces must be easy to identify and distinguish colors, can be used with the box or the surrounding environment harmonized views color. i) the cabinet can have a positive sign of China Unicom, manufacturers logos may not appear in the box front. Corridor (indoor and outdoor) optical sub-fiber box dimensions Cixi City for Wyatt Communication Equipment Co., Ltd. specializes in telecommunications, mobile, China Unicom, China Railcom, radio and television supply ancillary products, as follows: Optical Distribution Series (ODF): SC quick connectors optical fiber splice, fiber seat boxes, fiber panels, optical cable transfer me, fiber optic corridor boxes, fiber adapter, splice tray, fiber optic jumpers, pigtails, ODF wiring boxes, cable connector box, fiber panels, terminal , fiber distribution unit, fiber distribution frame (cabinet) and other Total with series (MDF): 10 loop security arrangements, 16 loop security arrangements, 25 loop security arrangements, 32-loop test row, 100 loop security arrangements 128 loop testing arrangements, various types of security units, alarm devices, main distribution frame. Various types of security units, alarm devices, main distribution frame (cabinet). Collocation series (DDF): Imitation Siemens Digital Distribution, Imitation NEC Digital Distribution, coaxial connector. Integrated wiring products: network patch panels, cable management, 110 wiring block, 5e, Category 6 modules, information panels, card access module, Cologne module junction box, network and communication tools and other communication products. The company has consistently adhered to "quality first, customer first, quality service, abide by the contract," the purpose, with high quality products, good reputation, high quality services, products sold. Wholeheartedly with the domestic business win-win cooperation and common development, create brilliant! Wyatt product integrity, cooperation to a long time! Sincerely look forward to your product pleasing sincere cooperation, promote friendship and look forward to establishing long-term good relationship with you [product] Yue communications service to create brand-name products, enhance their visibility and establish a corporate image, the company of "all the pursuit of quality, customer satisfaction for the purpose of "spirit," the most preferential price, the principle of the most attentive service, the most reliable product quality "to your solemn promise: a commitment to product quality: 1, manufacturing and testing products are quality records and inspection data. 2, the product performance testing, we sincerely invited users to visit the product whole process, all performance checks, was confirmed to be qualified before packing shipments. Second, the product price promise: 1, in order to ensure high reliability and advanced systems were chosen selection of domestic and international high-quality brand-name products. 2, in the same competitive conditions, our company not to reduce product on the basis of technical performance, change the product on the cost of parts, in good faith in the most favorable price to your party. Third, the delivery commitment: Product delivery: as requested by the user, if you have special requirements, be completed ahead of schedule, I may in particular organization of production, installation, and strive to meet customer needs. Fourth, the product Yuet service commitment: 1, the service aim: rapid, decisive, accurate, thoughtful and thorough 2, the service objectives: service quality to win customer satisfaction 3, service efficiency: the warranty period or outside, such as equipment failure, for party at short notice, maintenance personnel within 24 hours to reach the scene and begin repairs. 4, the service principles: product warranty period of twelve months, during the warranty period, the supplier will repair and replacement parts are quality causes damage, damage to parts of the warranty period, providing parts only cost fee, equipment damage caused by human factors from the demand side, the supply-side repair or provide parts at cost price according to plan. In the warranty period, our technical staff less than three times a year visit the user usage survey